Deck and fence staining in Vaughan
Deck and fence staining starts with clean, dry wood and ends with the stain and opacity that suit the species and the weather it takes. Vaughan is mostly recent builds and tear-down rebuilds through Woodbridge, Maple and Kleinburg with tall ceilings, heavy trim and builder flat paint, plus older postwar plaster houses in Thornhill. Older yards carry cedar decks and fences that have greyed and need brightening, and newer subdivisions carry pressure-treated decks that must dry out before a first coat.
Concept imageryVaughan, on the ground.
New houses have wide driveways, double garages and level entries, so the crew can set up a sealed spray area and scaffold indoors without trouble. The wood is washed, brightened and left to dry, failing stain is stripped, the surroundings are masked, and the stain goes on by brush and pad with railings done by hand.
A new house in Vaughan carries more trim than wall, so the quote is usually decided by the millwork and the spray setup rather than the square footage.
Read more about painters in Vaughan or the full deck and fence staining page.
On the quote, from the start.
- 01A moisture check on the wood and a look at the old finish to decide between a refresh and a strip
- 02Wash with a deck cleaner, then a brightener to lift the grey and open the grain
- 03Old stain stripped where it is failing, and smooth boards sanded so the new coat soaks in evenly
- 04Loose boards and popped screws reset, and badly rotted boards flagged for replacement before staining
- 05Stain applied by brush, pad or sprayed and back-brushed, with railings, spindles and stairs done by hand
- 06Plants, siding and patio stone masked, and a final walk around with you once the deck is dry to use
No figures published. The drivers, in order.
| Driver | What we look at |
|---|---|
| Square footage and railing length | The deck surface goes quickly. Spindles, stairs, lattice and the underside of a raised deck are brushed by hand and take most of the time. |
| Condition of the old finish | Bare or lightly weathered wood needs a wash and stain. A peeling solid stain needs stripping and sanding first, which can double the prep. |
| Type of stain | Transparent and semi-transparent stains go on in one coat and show the wood. Solid stains behave like paint and often take two. |
| Fence length and both sides | A fence is measured in linear metres, counted twice if we are doing your neighbour's side too. |
Weather sets the schedule. Stain needs dry wood, a dry forecast for a day or two after, and a surface that is not too hot, so a July heatwave can wait just as a wet May does.
Deck and fence staining questions from Vaughan
How early can you stain a deck in Vaughan?
Once Vaughan has a stretch of dry days with temperatures above the product's minimum and the wood reads dry on the meter, usually from [late May]. We book spring decks over the winter because the window fills quickly.
Can you stain my Vaughan fence on both sides?
Yes, with your neighbour's agreement for their side. It is the most common fence request in Vaughan because the colour and finish match from either yard. We mask their plantings the same as yours.
Our exterior is stucco over foam. Can it be painted, and with what?
Yes. Acrylic stucco is washed, hairline cracks and impact damage are repaired with a matching stucco patch, and the surface gets two coats of an elastomeric or high-build acrylic coating that bridges small cracks and sheds water. The colour change is the easy part. The repairs are what the quote is built on. Exterior stucco work is booked for the warmer months and dry weather.
The builder sprayed our whole house in one colour, ceilings included. Can you give us separate wall and ceiling colours?
Yes, and that is the usual first repaint in a new Vaughan house. The ceilings get a flat ceiling white, the walls a primer and two coats of the colour you choose, and the line between them is cut by hand so it is straight even where the drywall corner is not. It changes the whole house more than any furniture purchase, because builder monotone flattens every room.